Part Number: 1200022L2

Adtran T1 CSU Ace

The Adtran T1 CSU ACE is a compact, full-featured T1 channel service unit used to connect T1 data terminal equipment (DTE) and T1 facilities. The unit is designed to provide alarms, loopbacks, signal regeneration, line build out, and surge protection, as well as maintain 1s density for the DTE and T1 network.

Part Number: 1200022L2

• Provides T1 facility interface and jitter tolerance
• Transparent to ESF formatted data
• Automatic or manual line build-out configuration
• Desktop or wall-mount

Part Number: 1200023

Adtran Smart 16 Shelf

The Adtran Smart 16 Shelf holds up to 16 DSU, ISU, TSU and IQ rackmount modules. It has an internally mounted AC power supply to convert single input AC power to required shelf voltages. The shelf provides a rackmount, high-density solution for centralsite WAN connectivity requirements. It provides flexibility, allowing for a mixture of 16 WAN communication devices.

Part Number: 1200023

• Installation og 16 WAN devices
• Rack Mounted
• Internally mounted AC or DC power
• Local and remote configuration and control of up to 256 devices via single controller card
• Two power splts to house redundant power supplies

Part Number: 1200062L1

Adtran 56/64 DSU

The Adtran 56/64 DSU terminates 56/64k DDS link into customer V.35 DTE interface. It derives timing from the network and has a unit configuration via DIP switches.

Part Number: 1200062L1

• Loop and DTE rate matched
• Point-to-point, point-to-multipoint or frame relay
• Front panel status LEDs

Part Number: 1200065L1

Adtran TSU Multiplexer Series Module

Full Drop and Insert expansion module. Provides secondary T1 interface. Can only be installed in slot 6 in TSU 600/600e. Aggrgates mulitple voice only or voice and data services onto T1 or FT1 bandwidths.

Part Number: 1200065L1

Part Number: 1200082L1

Adtran #HS FXS+ Dual Voice

This board plugs into one of the TSU 600e's six expansion slots on the rear of the TSU 600e and is completely hot-swappable. It provides 2-wire voice-grade interfaces serving as the loop termination for central office line current and rining voltage.

Part Number: 1200082L1

• Hot-swappable
• Serves as loop termination for central office line

Part Number: 1200103L2

Adtran FXO

The Adtran FXO module provides two foreign exchange office (FXO) voice ports. It supports message waiting indication when used with Adtran FXS modules. It extends the phones lines to remote sites over T1/FT1 circuits.

Part Number: 1200103L2

• Two voice circuit connections to PBX or key system modules at distances up to 2,500 ft
• Available as plug-in or plug-on

Part Number: 1200106L3

Adtran E&M Dual Voice w/2713LB

Part Number: 1200106L3

Part Number: 1200114L1

Adtran DSX-1

The DSX-1 Modules is one of several expansion modules for the TSU multiplexer. This module is used when a standard DSX-1 interface is required, such as a connection to a PBX. The DSX-1 interface is provided on both both RJ-45C and DB-15 physical and electrical interfaces providing DTE distances to 655 feet.

Part Number: 1200114L1

• Expansion Modle for TSU multiplexer
• Distances up to 655 feet configuration occurs from front panel of TSU or optional mgmt sw
• Allows interface of older PBX's running SF framing to ESK facilities
• Monitoring and testing can be done from front panel or T-watch software

Part Number: 1200222L1

Adtran HDLC

The Adtran HDLC provides 128 HDLC controllers. This is required for PRI over T3 applications in the ATLAS 800/ATLAS 810. It supports public and private Frame Relay traffic that terminates on T1, E1, V.35, EIA-530, RS-449/V.36, X.21/V.11 or EIA-232

Part Number: 1200222L1

• Provides 128 HDLC controllers
• Supports private and public Frame Relay
• Occupies one slot and does not provide any physical external interfaces

Part Number: 1200291L1

AdtranMX2800 Patch Panel

The Adtran MX2800 Patch Panel provides 28 RJ connections for DSX-1 deployment. It fits in a 19-inch rack and includes two 6-foot, 64-pin cables to connect directly to the rear of the MX2800 or MX2810.

Part Number: 1200291L1

• 28 RJ connections
• Fits in 19-inch rack

Part Number: 1200295L1

Adtran TSU ACE DSU/CSU

The Adtran TSU ACE DSU/CSU provides single V.35 DTE interface for applications such as LAN-to-LAN bridging, Frame Relay circuit termination, and dedicated videoconferencing. The features include synchronous DTE rates in increments of 56Kbps or 64Kbps up to 1.536Mbps, remote configuration from host TSU via FDL or 8 K in-band.

Part Number: 1200295L1

• Single port with LCD display and front panel
• 4 button keypad. Single V.35 connector
• Supports remote configuration/monitoring

Part Number: 1202022L1

Adtran T1 CSU Ace 2nd Gen

The T1 CSU ACE provides T1 line-conditioning and jitter tolerance. This unit is typically used for voice line conditioning on a PBX. The unit is designed to provide alarms, loopback, signal regeneration, line build out, and surge protection.

Part Number: 1202022L1

• Front panel LEDs
• Wall or rack mountable
• Surge protection
• Compact, full-featured T1 channel service unit

Part Number: 1202060L1

Adtran TSU LT SA T1/FT1 DSU/CSU

The ADTRAN TSU LT is a low cost, full-featured T1/FT1 Data Service/ Channel Service Unit (DSU/CSU). The TSU LT provides an interface between T1 or Fractional T1 service and the end user's Data Terminal Equipment (DTE) for applications such as LAN to LAN bridging, Frame Relay circuit termination and videoconferencing. The TSU LT provides access to traditional dedicated point-to-point T1 services as well as network termination for Frame Relay.

Part Number: 1202060L1

• Housed in a compact, durable plastic housing
• Supports synchronous data rates from 56 kbps to 1.536 Mbps at Nx56 or Nx64 kbps
• TSU LT provides the capability to control a remote TSU LT through the T1 FDL channel

Part Number: 1202129L1

Adtran TSU 120e

The TSU 120e is a modular, full-featured T1-FT1 DSU/CSU designed to support a wide range of end-user applications. Equipped with both a synchronous V.35 DTE interface and a DSX-1 PBX port, the TSU 120e supports applications combining digital voice and high speed data. As interface requirements increase, the flexibility of the TSU 120e benefits the user with modularity through its expansion slot. To support critical data applications, the built-in V.35 interface on the TSU 120e can be converted to provide dial backup functionality during T1 failure conditions. Support for future growth, through the unit's single expansion slot, is a key feature of the TSU 120e.

Part Number: 1202129L1

• Provides complete monitoring and control of the T1 network

Part Number: 1203019L1

Adtran NT1 Ace 3rd Gen

The ADTRAN NT1 ACE provides the network termination for 2B1Q ISDN basic rate service. The NT1 ACE provides a 2B+D basic rate interface between the subscribers' terminal equipment and the ISDN network. The NT1 ACE monitors the S/T-interface for overcurrent fault conditions.

Part Number: 1203019L1

• Enclosed in durable plastic housing for desktop use
• Power supply provides up to 8.9 watts of power

Part Number: 1203022L1

Adtran CSU Ace 3rd Generation

The T1 CSU ACE provides an interface between T1 service and the end user's DSX interface such as a DTI T1 PBX interface. It transparently passes signal format and line coding. Equipped with T1 line conditioning and jitter tolerance.

Part Number: 1203022L1

• Supports framces or unframed signal formats
• Front panel status LEDs
• Desktop or wallmount

Part Number: 1203025L1

Adtran ESF CSU ACE 3rd Generation

The Adtran T1 ESF CSU ACE (33rd Generation interface T1 DTE equipment to Telco-provided or private T1 facility. It provides conversion for signal formats and line coding as well as T1 line conditioning and jitter tolerance.

Part Number: 1203025L1

• Enhanced alarm status, T1 performance reports, and test capabilities
• Transmits framed or unframed "all 1s" during signal loss from DTE or T1 network
• Front panel keypad and LCD screen

Part Number: 1204005L1

Adtran Modular 10BaseT Ethernet SNMP Interface card

Modular 10BaseT Ethernet SNMP Interface card, provides 10BaseT access to embedded SNMP agent in the following products: DSU IV ESP, DSU IQ, TSU ESP, TSU IQ and TSU IQ+.

Part Number: 1204005L1

Part Number: 1246026L4

Adtran T1 HDSL HTU-R TRCVR

Adtran T1 HDSL provides pair savings and DSl spectral compatibility. Uses four wires and up to three repearers to extend the carrier reach beyond the Carrier Serving Area. Allows for enhanced protection switching.

Part Number: 1246026L4

• Front panel LED's
• Front panel monitor jack
• Front panel loopback buttons
• Front panel DB-9 for diagnostics and testing

Part Number: 1280003L2

Adtran Tracer Baseband Processor 2T1

The Adtran Tracer Baseband Processor 2T1 provides system electrical and digital 2xDS-1/DSX-1 interfaces, user controls, indicators and spread spectrum processing.

Part Number: 1280003L2

• 19" rackmount
• Provides T1 transport up to 30 miles

Part Number: 4202023L1

Adtran Smart 16 Shelf 2nd Gen

The Adtran Smart 16 Shelf holds up to 16 DSU, ISU, TSU and IQ rackmount modules. It has an internally mounted AC power supply to convert single input AC power to required shelf voltages. The shelf provides a rackmount, high-density solution for centralsite WAN connectivity requirements. It provides flexibility, allowing for a mixture of 16 WAN communication devices.

Part Number: 4202023L1

• Installation og 16 WAN devices
• Rack Mounted
• Internally mounted AC or DC power
• Local and remote configuration and control of up to 256 devices via single controller card
• Two power splts to house redundant power supplies